NEW PRODUCTS

Black Soft top for 2000 (102) & 2600 (106) made in the original style cloth. SPECIAL ORDER We can also special-order alternative colours, Blue, Beige, Brown, Bordeaux and Green. Please contact us for availability and timescales...

Pair of velour door seals for GTV6 models. This type comes complete with the molded corner piece.

Bonnet hinge spacer to suit all 105 non-stepfront GTs.

Pair of alloy upper A-post covers to suit a 2600 spider. These covers sit on the underside of the upper portion of the A-panel inside the door shut. Please see photo 4 for a better idea of its location.

Light green tinted front windscreen to suit all later Alfetta GTVs with a bonded windscreen.

Complete early interior rear vision mirror with chrome surround - dipping style - to fit all 105 Series Coupes & Saloons up to 1968. Excellent quality. Also fitted to early 1750 berlina.

Hardtop rear screen seal to suit all Giulietta Spiders with a glass rear screen. If you require the seal for a plexiglass screen please see 750-421

Hardtop rear screen seal to suit all Giulietta Spiders with a plexiglass rear screen. If you require the seal for a glass screen please see 750-422

Boot striker spacer plate (1mm thickness) to suit all 105 GTs. This plate sits under the boot striker to marginally lower it if your boot lid isn't catching properly.

1966-70 Spider Roundtail rear reflector. only.

Rear soft top drape/cover for 101 series Giulietta Spider.

Soft top channel drain hose to suit 105 Spiders from 1970-93. This is the hose that runs down the B-post to the sill for drainage of the soft top channel. *Please note this hose will do both sides. It just needs to be cut in half and then trimmed to...

Glyco little end/conrod to gudgeon pin bearing to fit 101, 105, 116 and 75 engines, 1600, 1750, 2000 and V6 Busso engines. Also fits Montreal engines.

Headlamp bowl for late cars with ELMA headlight. Please check pictures carefully before purchasing to make sure this headlight bowl is correct for your headlight.

Exhaust tailpipe o-ring for the joint between the centre and rear sections of the exhaust on cars which require a 68mm O ring.

Spider boot hinge bolt 1966-1993. Please note ealry cars were fitted with a step rivet, which will need to be drilled out and can be replaced by this bolt.

Cylinder head nut for all 106 2600 cars.

105/115 series engine compartment strengthening panels. These panels fit in the area behind where the steering box and idler mount on the outside of the inner wing. Providing extra support and strengthening whilst also cutting down on unwanted body flex...

Bush engine block. Height is 14.5mm. locates the lower pulley in the block. MUST BE HONED 2000 engines.

Very rare set of Alfa Romeo main dealer 105 printing plates. We estimate these to be dated around 1969. These are collectors gold! The plates were made by Alfa Romeo to have ink rolled across them and then pressed into paper in a printing press for print...

Replica Vega style 6 x 14 inch 4 stud wheels to suit 4 cylinder Alfettas (not the GTV6), new reproduction of classic Seventies alloy wheel, finished in black with polished rim and highlights. 98 PCD Offset ET23 TUV approved.

New alloy reproduction of the Campagnolo Millerighe Montreal wheel. 6 x 14 inch, 4 stud with 108 PCD. Offset - ET23 Can also be fitted to later (1968 on) GT/GTV or Spider models.

Wiring loom to suit all left hand drive Junior Zagatos. PVC cables with correct style connectors and PVC outer sleeves/tape for protection.

Fuel sender to suit Alfetta GTV6s. For Alfetta Saloons and 4 cylinder Alfetta GTVs please see D0454